Rikon Power Tools 10-110B Manual del operador

50-142www.rikontools.com50-142M21” x 42” Belt / 8” Disc SanderOperator’s ManualRecord the serial number and date of purchase in your manual for future

10FIG. 15ASSEMBLYCalifornia Proposition 65 WarningWARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction acti

11DISC SANDING1. Depending on what type of sanding that you will be doing, set the Sanding Disc Table to the proper angle from 45° to 90°.2. Once th

12FIG. 19OPERATIONFIG. 21 Always ensure the sander is unplugged prior to attempting any assembly, installation or changing of parts and accessories.BE

OPERATIONFIG. 22FIG. 2313CHANGING THE SANDING BELT1. Remove the plastic Cover (#43) from the frame by unscrewing the two knobs (#41).2. Tilt the san

ADJUSTMENTS14FIG. 24FIG. 26FIG. 27DISC TABLE ADJUSTMENTSEnsure sander is disconnected from the power supply prior to commencing work.1. To check the t

15ADJUSTMENTSV-BELT TENSION ADJUSTMENTSEnsure sander is disconnected from the power supply prior to commencing work.Should the rotation of the sanding

16 This machine must be grounded. Replacement of the power supply cable should only be done by a qualied electrician.

EXTENSION CORDS Keep the extension cord clear of the working area. Position the cord so that it will not get caught on

PARTS EXPLOSIONSANDING BELT & MOTOR7562322224252618279345462829448471230495051521011181413151617192021323334 373839353656-B5356-A41625556595443575

19PARTS LISTHex Socket Head Screw M10Flat Washer 10mmSpring Spacer Belt Tracking Knob & ScrewSpringSupport BracketPinShaft ShaftHex Screw

SAFETY INSTRUCTIONSIMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be

PARTS EXPLOSIONSANDING DISC & SWITCH10099106105104121120131631321371391411091081071104712512212412312812714414313014014212913413313658135606110110

PARTS LIST21Handle AssemblyLock Washer 8mmScrew M8BaseWasher 4mmSandpaper Disc 8” PSASanding Disc Plate 8”Hex Screw M5 Screw

NOTESUse this section to record maintenance, service and any calls to Technical Support:22

2323WARRANTY

www.rikontools.com50-142M250-142For more information:16 Progress RdBillerica, MA 01821877-884-5167 / [email protected]

SAVE THESE INSTRUCTIONS.Refer to them often.3California Proposition 65 WarningWARNING: Some dust created by power sanding, sawing, grinding, drilling,

TABLE OF CONTENTSSPECIFICATIONS4Model Number Belt SizeBelt SpeedDisc Size (PSA)Disc SpeedDust Ports (2)Motor HPMotor Volts / AmpsNet Weight50-1421”

5CONTENTS OF PACKAGECarefully unpack your sander from its carton, and check to make sure the following parts are included. If any parts are missing or

6THE SANDER MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE.GETTING TO KNOW YOUR SANDERASSEMBLYItem

FIG. 1 FIG. 2 FIG. 3ASSEMBLYFIG. 4FIG. 57 Always ensure the sander

8 ASSEMBLY FIG. 6 FIG. 7 FIG. 8 FIG. 9INSTALL THE I

9 FIG. 10 FIG. 11ASSEMBLY FIG. 12INSTALL THE DISC SANDING TABLE21.